Brushless Motors BLH Series

BLHM015K-30

Print Product Information All at once
BLHM015K-30

Motor
Product Classification Product Name CIF: List Price FOB: List Price Shipping Date
Motor BLHM015K-30 MYR 883 MYR 779 5 Working Days
• This product is a motor only of the brushless motor. A combination of driver circuit and connection cable is required for driving.

Included

  • Motor: None

Specifications

Dimensions

Geared Motor
Geared Motor

Geared Motor

Data Download

Other Specifications

General Specifications

Item Motor Driver
Insulation Resistance 100 MΩ or more when a 500 VDC megger is applied between the windings and the case after continuous operation under normal ambient temperature and humidity.
 		 After continuous operation at normal ambient temperature and humidity, the value measured with a 500 VDC megger between the power supply input and the heat sink is min. 100 MΩ.
 
Dielectric Strength No abnormality is observed even with an application of 1.5 kVAC at 50 Hz between the coils and the case for 1 minute after continuous operation at normal ambient temperature and humidity.
 		 After continuous operation at normal ambient temperature and humidity, the value measured with a 500 VDC megger between the power supply input and the heat sink is min. 100 MΩ.
 
(Except for RS-485 communication type)
Temperature Rise After continuous operation at normal ambient temperature and humidity,
the measured value using the thermocouple method is 50 °Cmax. for the temperature rise of the coils
and 40°C*1 max. for the temperature rise on the case surface.		 After continuous operation at normal ambient temperature and humidity, the measurement value of the temperature rise of the heat sink is 50 °C max. using the thermocouple method.
 
Operating Environment Ambient Temperature 0∼+50°C (Non-freezing)
Ambient Humidity 85 % max. (Non-condensing)
Altitude Up to 1000 m above sea level
Atmosphere No corrosive gases or dust Should not be exposed to water or oil.
Cannot be used in a radioactive area, magnetic field, vacuum, or other special environments.
Vibration Must not be subjected to continuous vibration or excessive shock.
Conforms to JIS C 60068-2-6, "Sine-wave vibration test method."
Frequency Range: 10~55 Hz, Half Amplitude: 0.15 mm　
Sweep direction: 3 directions (X, Y, Z) Number of sweeps: 20
Storage Condition*2 Ambient Temperature -25~+70°C (Non-freezing)
Electromagnetic Brake Motor: -20~+70°C (Non-freezing) 		-25~+70°C (Non-freezing)
Ambient Humidity 85 % max. (Non-condensing)
Altitude Up to 3000 m above sea level
Atmosphere No corrosive gases or dust Should not be exposed to water or oil.
Cannot be used in a radioactive area, magnetic field, vacuum, or other special environments.
Thermal Class UL/CSA Standards: 105 (A), EN Standards: 120 (E) −
Degree of Protection Connector Type/Lead Wire Type IP40
Cable Type, Electromagnetic Brake Motor: IP65
excluding the connector section and the round shaft type mounting surface)		 IP00
*1
Attach round shaft types to a heat sink (Material: aluminum) of one of the following sizes to maintain a motor case surface temperature of 90 °C max. (Except BLHM015.)

Heat Sink Size

Product Name Size (mm) Thickness (mm)
BLM015, BLM030, BLM230, BLHM230 115x115 5
BLM250, BLM 450, BLHM450 135x135
BLHM5100 200x200
*2
The value for storage condition applies to short periods such as the period during transport.

Note

  • Do not measure insulation resistance or perform a dielectric strength test the motor and driver are connected.

Permissible Radial Load and Permissible Axial Load

Parallel Shaft Gearhead

Output Gear Ratio Permissible Radial Load Permissible Axial Load
N
10 mm From Shaft End
N 		20 mm From Shaft End
N
15 W 5, 10, 15, 20
30, 50, 100		 50 − 30
30 W 5 100 150 40
10, 15, 20 150 200
30, 50, 100, 200 200 300
50 W 5 200 250 100
10, 15, 20 300 350
30, 50, 100, 200 450 550
100 W 5 300 400 150
10, 15, 20 400 500
30, 50, 100, 200 500 650
Radial Load and Axial Load

CS Geared Motor

Output Gear Ratio Permissible Radial Load Permissible Axial Load
N
10 mm From the End of the Output Shaft
N 		20 mm From the End of the Output Shaft
N
□42mm-15 W
□42mm-30 W		 5 50 - 40
10, 15, 20 80 -
□60mm-30 W
□60mm-50 W		 5 150 190 70
10, 15, 20 200 260
CS Geared_Radial Load_Axial Load

Hollow Shaft Flat Gearhead

Output Gear Ratio Permissible Radial Load Permissible Axial Load
N
10 mm From the Gearhead Mounting Surface
N 		20 mm From the Gearhead Mounting Surface
N
30 W 5, 10 450 370 200
15, 20, 30, 50, 100, 200 500 400
50 W 5, 10 800 660 400
15, 20, 30, 50, 100, 200 1200 1000
100 W 5, 10 900 770 500
15, 20 1300 1110
30, 50, 100, 200 1500 1280
Radial Load and Axial Load Illustration

Round Shaft Type

Output Permissible Radial Load Permissible Axial Load
N
10 mm From Shaft End
N 		20 mm From Shaft End
N
□42mm-15 W
□42mm-30 W		 50 − 5
□60mm-30 W
□60mm-50 W		 70 100 15 (10) *
□80 mm-50 W 120 140 20
□90 mm-100 W 160 170 25
  • *The values in parentheses ( ) are for electromagnetic brake motor.

Cables and Accessories

Data Download
Print Product Information All at once
close
close
close